On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
All American 1930 Pressure Cooker/Canner9.6/10View on Amazon - 2
All American 930 Canner9.6/10View on Amazon - 3
All American 1930 Pressure Cooker/Canner9.5/10View on Amazon
When the garden gives more than the family can eat fresh, the canner comes out of the cupboard and every part on it earns its keep. All american canner parts are the pieces that wear, loosen or go missing between seasons: the gauge that reads pressure, the regulator that holds it steady, the vent pipe and the overpressure plug that keep it safe. This guide lists each part, explains what it does and shows how to match a replacement to the canner in front of you, using the part numbers the listings state.
HarvestGearLab earns a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
All american canner parts: the short list
Most pressure canners share the same small set of parts. The table shows what each one does and when it needs attention.
| Part | What it does | When to check it |
|---|---|---|
| Pressure gauge | Reads the pressure inside the canner | Before the season and after a drop or knock |
| Regulator weight | Holds the pressure steady while the canner runs | When the rocking or hissing pattern changes |
| Vent pipe | Lets steam escape and carries the regulator | When it looks blocked or the regulator sits crooked |
| Overpressure plug | Vents steam if pressure climbs too high | When it looks cracked, hard or swollen |
| Sealing ring, 09985 | Seals the lid to the body on Presto canners | When the seal leaks or the ring hardens |
| Gauge fastener pack, 82248 | Seals the gauge to the lid with washers, nut and gasket | When steam escapes around the gauge |
Start with the seal: All American has no gasket
The first thing to know about All American canner parts is that the canner has no gasket. All American canners seal metal to metal, with a lid that clamps down on the body, so there is no rubber ring to replace and no gasket in the parts list. That is the main difference from Presto and Mirro canners, which use a sealing ring between lid and body. If a parts listing offers a gasket, it belongs to a Presto or Mirro canner, not to an All American, and buying by part number keeps the wrong ring out of the cart.
What does wear on an All American is the metal itself: the sealing surfaces on lid and body, the clamps that pull them together, the gauge, the regulator weight and the overpressure plug. Keep the sealing faces clean and free of nicks, keep the clamps snug and even, and treat the gauge as the part that needs checking most often.
The gauge and its fasteners
The pressure gauge is the part you read all day, so a gauge that reads wrong is the part to fix first. The Gfdoso 82248 gauge fastener (on Amazon) pack fits Presto pressure canner steam gauge models 82121, 82237 and 85772, and the pack includes 5 washers, 5 nuts and 5 gaskets, enough for several gauge refits. The spec table lists a size of 0.7087 inches and 15 items in the pack. A fresh washer and gasket under the gauge stops steam escaping around the fitting and keeps the reading steady, and the stainless steel and rubber parts in the pack are made to stand up to heat and pressure.
When a dial gauge has been dropped or knocked, ask a local extension office whether they can check it before the next batch. Our pressure canner gauge for All American guide lines up gauges by fit and style, and the pressure canner gauges guide covers budget options.
Gaskets: Presto and Mirro part numbers
Presto canners take the 09985 sealing ring, and the listings agree on the fit: Presto models 0174510 for 16 qt, 0175107 for 18 qt, 0175510 for 16 qt, 0178107 for 23 qt, 0178209 for 23 qt and 0178410 for 23 qt. The Ulreon ring (on Amazon) is BPA-free food-grade silicone, heat-resistant up to 450 degrees F (232 degrees C), and the 2-pack ships with 4 plugs, so there is always a spare ring and plug on hand. The ANTOBLE listing gives the same fit and adds the maker’s advice to replace the gasket every 1-2 years so the canner keeps working well.
To fit a new ring, remove the old ring and plug, clean the groove, then work the new ring into the lid a small section at a time until it sits fully in place. Push the round side of the overpressure plug, marked TOP, into its opening from the underside of the cover, then open and close the cover several times so it moves freely. Mirro canners take a different ring: the GUSUUI S-3440 gasket (on Amazon) fits Mirro models M-312, M-312-35, M-406, M-416, M-512, M-512-11, M-522, M-526, M-526-11 and M-622 manufactured before January 1983, and the listing advises checking the date stamp on the bottom of the canner to confirm the match. Our pressure canner gasket for Presto guide compares gasket listings, and the low-cost gaskets guide covers low-cost rings.
What to skip or double-check
- A Presto gasket in an All American canner: skip it. All American canners have no gasket, so a sealing ring has nowhere to sit.
- Processing jars in the oven: skip it. Dry oven heat is not a safe way to process canning jars.
- Electric pressure cookers: do not use one for canning unless the maker states it is made for pressure canning.
- A gauge that has been dropped: check it before use, and ask a local extension office whether they can check a dial gauge.
- Old or secondhand canners: check the gauge, seal and safety plug before use, and confirm the model number before ordering parts.
- Reused single-use lids: buy new flat lids each season.
What this guide does not cover
This is a parts guide. It does not give recipes, processing times, pressures, headspace figures or altitude changes. Take those from current USDA and National Center for Home Food Preservation guidance, or from a current edition of a trusted canning guide, and follow them exactly for each food. For the canner itself, our pressure canner for home canning guide compares current options, and the All American canner for induction cooktop guide covers stovetop fit.
FAQ: preserving at home
Does an All American canner use a gasket?
No. All American canners seal metal to metal, with no rubber ring between lid and body. Gaskets such as the 09985 belong to Presto canners, and the S-3440 belongs to Mirro canners.
Which gasket fits a Presto pressure canner?
The 09985 sealing ring fits Presto models 0174510, 0175107, 0175510, 0178107, 0178209 and 0178410, covering 16 qt, 18 qt and 23 qt canners. Confirm the model number on the canner before ordering.
How often should a canner gasket be replaced?
The ANTOBLE listing recommends replacing the gasket every 1-2 years so the pressure cooker keeps working well. Replace it sooner if the seal leaks or the ring hardens.
What comes in a pressure gauge fastener pack?
The 82248 pack includes 5 washers, 5 nuts and 5 gaskets, 15 items in all, and fits Presto steam gauge models 82121, 82237 and 85772. It seals the gauge to the lid and stops steam escaping around the fitting.
How do I match a Mirro gasket to my canner?
The S-3440 gasket fits Mirro models M-312, M-312-35, M-406, M-416, M-512, M-512-11, M-522, M-526, M-526-11 and M-622 manufactured before January 1983. Check the date stamp on the bottom of the canner to confirm the match.
More preserving guides
See the pressure canner gaskets for Presto, the pressure canner gauge for All American and the pressure canners for home canning guides.
More picks: All American canners for induction cooktops, canning tool kits under 30, pressure canner gauges and canning racks for pressure canners.





