Skip to content
Independent guides to preserving gear, est. 2026

Canning, drying, storing and harvest gear for home kitchens

We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals
Kitchenaid Meat Grinder Attachment How to Use: A Step-by-Step Guide
Harvest and Processing

Kitchenaid Meat Grinder Attachment How to Use: A Step-by-Step Guide

A plain step-by-step guide to fitting a meat grinder attachment, grinding beef, pork and venison, and cleaning the parts after.

On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1InnoMoon Meat Grinder and Slicer Shredder Attachment forInnoMoon Meat Grinder and Slicer Shredder Attachment for9.6/10View on Amazon
  2. 2GVODE Stainless Steel Meat Grinder Attachment for KitchenAidGVODE Stainless Steel Meat Grinder Attachment for KitchenAid9.6/10View on Amazon
  3. 3GVODE Stainless Steel Meat Grinder Attachment for KitchenAidGVODE Stainless Steel Meat Grinder Attachment for KitchenAid9.6/10View on Amazon
  4. 4COFUN Meat Grinder & Slicer Shredder Attachments forCOFUN Meat Grinder & Slicer Shredder Attachments forView on Amazon
  5. 5HOZODO Meat Grinder & Slicer Shredder Attachments forHOZODO Meat Grinder & Slicer Shredder Attachments forView on Amazon
  6. 6Cuisinart MG-50 Meat Grinder Attachment for SM-50 and SMD-50Cuisinart MG-50 Meat Grinder Attachment for SM-50 and SMD-50View on Amazon
  7. 7Meat Grinder Attachment for the Bosch Universal Plus KitchenMeat Grinder Attachment for the Bosch Universal Plus KitchenView on Amazon
  8. 8LEM #8 Patty Maker Attachment for Meat GrindersLEM #8 Patty Maker Attachment for Meat GrindersView on Amazon
  9. 9LEM Products BigBite Jerky Slicer and Tenderizer AttachmentLEM Products BigBite Jerky Slicer and Tenderizer AttachmentView on Amazon

A freezer full of venison and pork from the fall harvest still needs turning into sausage and burger, and the stand mixer on the counter can do the grinding with the right attachment. Kitchenaid meat grinder attachment how to use is the question that stands between whole cuts and ground meat, and the answer is a short routine: fit the attachment to the mixer, prepare cold meat, feed it through in steady passes, then take the parts apart and clean them. This guide walks through each part of that routine, with the sizes and limits the listings state.

Runners-up to consider

HarvestGearLab earns a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

Kitchenaid meat grinder attachment how to use: the short version

The attachment fits the power hub on the front of the mixer, where the hub cover lifts away, and the ring locks the grinder head in place. Cold meat feeds through the tube with the pan and pusher, the worm turns it against the chopper knife and plate, and ground meat comes out the front. A #12 attachment, such as the ALFA #12, suits Hobart-style power hubs, and the ALFA listing states a weight of 17.1 pounds. Grinding goes faster when the meat stays cold and the pieces fit the tube, and the whole routine ends with washing and drying each part.

Fit the attachment to the mixer

Start with the mixer switched off and the hub cover removed from the front power hub. Slide the grinder head into the hub until it seats, then turn the ring to lock it in place so the head cannot wobble while the worm turns. Set the pan on top of the head and check that the ring, worm, knife and plate sit in the order the maker lists: grinding cylinder head, pan, ring and worm, with the chopper knife and chopper plate inside. The ALFA set ships with a chopper plate that measures 1/4 inch, and that plate sets the size of the grind. A loose ring lets the head shift under load, so tighten it before any meat goes in.

Part What it does
Grinding cylinder head Holds the worm, knife and plate in line
Pan Holds meat above the feed tube
Ring Locks the head to the power hub
Worm Turns meat toward the knife and plate
Chopper knife Cuts meat against the plate
Chopper plate (1/4 inch) Sets the size of the grind

Prepare the meat and the parts

Cold meat grinds cleanly and warm meat smears, so keep the meat chilled until it goes in the tube, and chill the grinder head and plate with it when the kitchen runs warm. Cut the meat into strips that slide down the feed tube without forcing, and trim away gristle and bone before grinding, since hard bits can jam the worm. The ALFA listing states its attachment is intended for grinding beef, pork, and venison only, and it is not suitable for poultry, seafood, cheese, or vegetables. Keep each kind of meat apart while grinding so sausage and burger stay true to the cut that went in. The best meat grinder for venison guide lines up grinders for a deer harvest, and the best meat grinder for pork guide covers pork in the same way.

Grind in steady passes

Run the mixer at a low speed and feed the strips into the tube with the pan holding the meat above the worm. Use the pusher to guide each strip down, and let the worm pull the meat through the knife and plate at its own pace instead of pressing hard. If the flow slows, stop the mixer, clear the plate, and look for gristle or a dull edge before starting again. Ground meat should fall into a chilled bowl below the head, and another pass through the plate gives a finer grind for sausage when the recipe calls for it.

What the attachment will and will not grind

The meat matters as much as the fit. The ALFA #12 listing states its attachment is intended for beef, pork, and venison only, so plan sausage, burger and ground venison around those cuts and leave poultry, seafood, cheese and vegetables out of the grinder. A #12 head suits a steady batch of red meat, and the meat grinder sizes guide explains how the sizes line up. Material matters too: the metal vs plastic meat grinder attachment comparison walks through the trade between a heavy metal head and a lighter plastic head.

Clean up and storage

Take the head apart as soon as grinding ends, while the meat residue is still soft, and wash each part in warm soapy water, then dry each part fully before storage so the metal stays free of rust. The knife and plate need care in handling since the edges cut, and a dry cloth keeps them clean between uses. Store the parts together in the pan or a labeled box so the ring, worm, knife and plate are ready for the next batch. A quick wash after each use keeps the attachment ready and avoids dried residue in the worm threads.

FAQ: preserving at home

How do you attach a meat grinder attachment to a KitchenAid mixer?

Remove the hub cover from the front power hub, slide the grinder head in until it seats, and turn the ring to lock it. The pan sits on top of the head, and the worm, knife and plate sit inside in the order the maker lists.

What meat can you grind with a meat grinder attachment?

The ALFA #12 listing states its attachment is intended for beef, pork, and venison only. It is not suitable for poultry, seafood, cheese, or vegetables.

What size plate comes with a #12 meat grinder attachment?

The ALFA #12 set includes a chopper plate that measures 1/4 inch. That plate sets the size of the grind for sausage and burger.

How heavy is a #12 meat grinder attachment?

The ALFA #12 lists a weight of 17.1 pounds. Plan counter space and storage for a heavy metal head before it arrives.

How do you clean a meat grinder attachment?

Take the head apart while residue is still soft, wash each part in warm soapy water, and dry each part fully before storage. Handle the knife and plate with care, since the edges cut.

More preserving guides

See the best meat grinder attachment guide, the meat grinder sizes guide, and the best meat grinder attachment for Kitchenaid mixer picks.

More picks: meat grinders for venison, meat grinders for pork, meat grinders for beef and metal vs plastic attachments.

Read next in the kitchen