Skip to content
Independent guides to preserving gear, est. 2026

Canning, drying, storing and harvest gear for home kitchens

We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals
Ball Lock vs Pin Lock Keg: Which One Should You Buy?
Beer Brewing

Ball Lock vs Pin Lock Keg: Which One Should You Buy?

Ball lock and pin lock kegs take different fittings, so match the fitting to the keg; this guide covers four ball lock fittings and the one stated pin lock fact.

On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Hgkeke Ball Lock Keg Tap Faucet and 0-60PSI CO2 Regulator SetHgkeke Ball Lock Keg Tap Faucet and 0-60PSI CO2 Regulator Set9.7/10View on Amazon
  2. 2Dbgogo Ball Lock Keg ConnectorsDbgogo Ball Lock Keg ConnectorsView on Amazon
  3. 3Cornelius Keg Ball Lock DisconnectCornelius Keg Ball Lock DisconnectView on Amazon
  4. 4FERRODAY Ball Lock Keg DisconnectFERRODAY Ball Lock Keg DisconnectView on Amazon
  5. 5FERRODAY Ball Lock Keg Fittings DisconnectFERRODAY Ball Lock Keg Fittings DisconnectView on Amazon
  6. 66Pcs Keg Disconnect Ball Lock Keg Fitting Set Grey Quick Ball6Pcs Keg Disconnect Ball Lock Keg Fitting Set Grey Quick BallView on Amazon
  7. 76Pcs Keg Disconnect Ball Lock Keg Fitting Set Black Quick6Pcs Keg Disconnect Ball Lock Keg Fitting Set Black QuickView on Amazon

Ball lock vs pin lock keg comes down to this: the fitting has to match the keg. Ball lock and pin lock use different posts and disconnects, and a ball lock fitting does not fit a pin lock keg. Every fitting covered in this guide is ball lock, and no pin lock fitting is listed here, so buy ball lock if you are building a new setup from these listings, and match the fitting to the keg you already own.

Runners-up to consider

HarvestGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

Ball lock vs pin lock keg: the short answer

The four fittings in this guide are all ball lock. No pin lock fitting is listed here, so the pin lock side is covered by one stated fact: MRbrew says its ball lock posts are not suitable for pin lock kegs. That is the whole comparison on the pin lock side, and it is enough to set the rule: match the fitting to the keg. The table below lines up the four ball lock fittings by what they are and what they connect with.

Fitting What it is Gas barb Liquid barb Post thread
Dbgogo Ball Lock Set Posts and disconnects 5/16 in 1/4 in 19/32-18
Ferroday Ball Lock Disconnect, 2 Pack Disconnects 5/16 in 1/4 in Not stated
MRbrew Ball Lock Keg Post, 2 Pair Posts Not stated Not stated 19/32-18
LUCKEG Ball Lock Gas Disconnect Gas disconnect only 5/16 in swivel nut Not stated Not stated

How ball lock fittings connect

Ball lock tells you which disconnect goes where by color. The gas disconnect is gray or white and takes the 5/16 inch barb, and the liquid disconnect is black and takes the 1/4 inch barb. Dbgogo and Ferroday both state that split, and Ferroday adds 4 hose clamps to hold the hoses on the barbs. The posts use a 19/32-18 thread, stated by Dbgogo and MRbrew, and MRbrew marks the gas post with etches for the gas in port and leaves the liquid post unetched for the beer out port. LUCKEG and Ferroday use MFL swivel nuts on the disconnects, so they thread onto flared fittings rather than taking a barb alone. Sealing comes from the O-rings and gaskets in the box: Dbgogo includes 4 spare O-rings for keg posts plus gasket washers and hose clamps, and MRbrew includes 8 poppet O-rings and 8 post gaskets with its 2 pair of posts.

What to buy for a ball lock setup

Start from what you are replacing. If you need posts and disconnects together, the Dbgogo set is the only one here that includes both, with stainless posts, plastic disconnects, silicone O-rings and 4 spare O-rings. If your posts are fine and only the disconnects are worn, the Ferroday 2 pack gives a gas and a liquid disconnect with stainless swivel nuts, barbs and 4 hose clamps. If the posts themselves need replacing, the MRbrew kit gives 2 gas posts and 2 liquid posts with 4 springs, 4 poppets, 8 poppet O-rings and 8 gaskets, all in stainless. If you only need the gas side, the LUCKEG disconnect is a gas disconnect only, with a 1/4 MFL fitting, a 5/16 inch swivel nut and 2 worm clamps, and it leaves the liquid side for a separate purchase. See our plastic vs stainless steel keg guide if you are still choosing the keg itself, and our best beer keg dispenser guide for the tap side of the setup.

Pin lock: what changes

Pin lock kegs take pin lock posts and disconnects, which are different parts from the ball lock fittings listed here. No pin lock fitting is listed in this guide, so there are no stated pin lock sizes, threads or part counts to compare against the ball lock figures above. The one stated pin lock fact is MRbrew’s line that its ball lock posts are not suitable for pin lock kegs. If you own a pin lock keg, buy pin lock fittings for it. If you are buying a keg and fittings together and want the parts listed here, buy a ball lock keg.

What to skip or double-check

  • Ball lock posts on a pin lock keg: skip it. MRbrew states its ball lock posts are not suitable for pin lock kegs.
  • Sankey kegs: ball lock fittings work with a Sankey keg only with a keg coupler adapter, as Dbgogo and Ferroday state.
  • Barb sizes: match the 5/16 inch gas barb and the 1/4 inch liquid barb to your hose before you order.
  • Spares in the box: count the O-rings and gaskets before you order extras. Dbgogo includes 4 spare O-rings, and MRbrew includes 8 poppet O-rings and 8 gaskets.
  • Materials: Dbgogo and MRbrew posts are stainless, Ferroday uses ABS bodies with stainless swivel nuts, barbs and clamps, and LUCKEG uses PBT for the disconnect with stainless swivel nuts.

What this guide does not cover

This is a fitting comparison. It does not cover the kegs themselves, regulators, taps or gas lines beyond what the four listings state, and it does not give carbonation settings or line lengths. Every beer brewing guide on the site is collected in our beer brewing section.

FAQ: preserving at home

Can I use a ball lock disconnect on a pin lock keg?

No. MRbrew states its ball lock posts are not suitable for pin lock kegs, and the posts and disconnects in this guide are made for ball lock kegs.

Which disconnect is gas and which is liquid?

The gas disconnect is gray or white and uses the 5/16 inch barb, and the liquid disconnect is black and uses the 1/4 inch barb.

What thread do ball lock keg posts use?

The Dbgogo and MRbrew posts use a 19/32-18 thread.

What does the Dbgogo set include?

Ball lock gas and liquid posts, quick disconnects, sealing gasket washers, hose clamps and 4 spare O-rings for keg posts.

More preserving guides

See every beer brewing guide and all home brewing and wine guides.

More picks: beer keg dispensers, plastic vs stainless steel keg, kegerator vs keezer and kegerator cleaning kits.

Read next in the kitchen