On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
FastRack Red Baron Bottle Capper9.6/10View on Amazon - 2
WENNING Manual Bottle Capper WN0059.6/10View on Amazon - 3
WENNING Manual Bottle Capper WN0029.6/10View on Amazon
How to use a bottle capper is the question that comes up once the brew is ready and a row of filled bottles waits on the counter. The short answer: match the cap size to the bottle, set the cap in the bell, place the bottle under it, and press the lever or squeeze the handles until the cap crimps tight. This guide walks through each part of that motion, the capper styles in the listings, and the small checks that keep a batch sealed.
HarvestGearLab earns a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
How to use a bottle capper: the short version
A bottle capper is a small press with a bell that folds the edge of a crown cap over the lip of the bottle. The table shows the styles in the listings and what each one does.
| Capper | How it works | Caps it fits |
|---|---|---|
| Bench capper | Sits on a bench; a lever presses the bell down onto the cap | 26mm and 29mm crown caps |
| Double-lever hand capper | Handles on both sides squeeze the bell down over the cap | 26mm crown caps |
| Magnetic bell | Holds the cap in place while the bottle moves under it | 26mm crown caps |
Match the cap to the bottle
Most homebrew bottles take a 26mm crown cap. The FastRack, QWORK, Hgkeke and Fermentaholics listings all name 26mm caps, and the MRbrew capper (on Amazon) is made for 1.02″ crown caps. A few bench cappers take a larger bell as well: the North Mountain Supply capper (on Amazon) ships with 2 sizes of crimping bells and works with 26mm caps as well as 29mm caps, and the HomDSim bench capper (on Amazon) caps both 26 and 29 mm bottles. The bottle cap size guide shows how the sizes compare. Check the cap size before capping a batch, and keep both sizes apart if the capper ships with both bells.
The bottle matters as much as the cap. The Hgkeke capper (on Amazon) is made for standard 12oz / 330ml long-neck beer bottles and other non-threaded 26mm crown bottles, and it works with two-way reusable bottles, but it is not recommended for stubby, short-neck, or thin-walled single-use bottles. The MRbrew capper fits single-edge smooth lip bottles with no threads, so a twist-off or threaded neck does not fit the bell.
Set up a bench capper
Bench cappers adjust to the bottle. The FastRack Colt Strong adjusts for different bottle sizes with a spring-mounted lever, the QWORK capper (on Amazon) adjusts height with a quick-turn mechanism, and the HomDSim capper is vertically adjustable for different bottle sizes. Set the height so the bell meets the cap with the lever at the top of its travel, then lock it in place before capping the batch.
Keep the base still. The FastRack Colt Strong has a non-slip textured base with pre-drilled holes for bolting to a workbench, the Ferrari Super Agata has a wide metal base with a non-slip rubber pad and pre-drilled holes, and the HomDSim capper has a textured non-slip base with built-in holes for bolting down. A capper that slides across the bench gives an uneven crimp, so bolt it down or brace it before capping the batch.
Bench cappers are bench-sized tools. The FastRack Colt Strong measures 21.81 inches x 8.74 inches x 7.17 inches, and the Ferrari Super Agata measures 6.6 inches x 8.75 inches x 19.75 inches, while the Fermentaholics double-winged hand capper measures 7.25 inches x 5.88 inches x 2.63 inches and weighs 1.0 pounds. Give the bench capper a clear spot with room for the lever to swing, and keep the caps within reach.
Cap a bottle, step by step
Fill the bottle and set it on the base. Place a cap under the magnetic bell, with the magnet holding it in place. Slide the bottle under the bell so the cap sits square on the mouth. Press the lever down in a smooth motion, or squeeze the handles of a hand capper together, until the bell crimps the cap onto the lip. Lift the lever, pull the bottle out, and look at the cap: the crimp should run even all the way around, with no gap and no tilt.
Cap the batch the same way, bottle after bottle. If a cap sits crooked, lift it off and start that bottle again with a fresh cap, since a cap that crimps unevenly may not hold its seal.
Caps, counts and batches
Many cappers arrive as kits with caps in the box. The MRbrew capper comes with 100 beer bottle caps, the Craft A Brew kit includes 100 bottle caps, the Thermometer World capper includes 120 caps, and the Hgkeke kit comes with 150 crown caps in 3 colors: 50 silver, 50 black, 50 copper. The colors suit color-coding batches, so a brewer can tell one batch from another by the cap.
A 100-count bag of caps covers ten 1 gallon batches or two 5 gallon batches, according to the Craft A Brew kit listing, and one gallon of beer or cider yields about eight to ten 12 oz bottles. Count the bottles before capping day, and keep spare caps on hand for any cap that lands on the floor or crimps crooked.
What to skip or double-check
- Threaded bottles: the MRbrew capper fits single-edge smooth lip bottles with no threads, so a twist-off neck does not fit the bell.
- Stubby, short-neck, or thin-walled single-use bottles: the Hgkeke capper is not recommended for them.
- Cap size: match the bell to the cap; a capper that ships with 2 sizes of bells needs the right bell for the cap in hand.
- A loose bench: bolt the base down or brace it before capping, using the pre-drilled holes the FastRack, Ferrari and HomDSim cappers list.
What this guide does not cover
This guide covers capping only. It does not give brewing recipes, fermentation schedules or carbonation levels; take those from the recipe kit in use and follow its instructions for each batch. Every homebrewing guide on the site is collected in the home brewing section.
FAQ: preserving at home
What size cap does a bottle capper use?
Most homebrew cappers use 26mm crown caps. The MRbrew capper is made for 1.02″ crown caps, and bench cappers from North Mountain Supply and HomDSim also fit 29mm caps with a larger bell.
Do bench cappers fit bottles of different heights?
Yes. The FastRack Colt Strong, the QWORK and the HomDSim bench cappers all adjust in height for different bottle sizes. Set the height before the batch, then leave it alone while capping.
Do bottle cappers come with caps?
Some do. The MRbrew capper and the Craft A Brew kit each include 100 caps, the Thermometer World capper includes 120 caps, and the Hgkeke kit includes 150 caps in 3 colors.
Can I use a bottle capper on a threaded bottle?
No. The MRbrew capper fits single-edge smooth lip bottles with no threads, so a threaded or twist-off neck does not fit the bell.
What is the difference between a bench capper and a wing capper?
A bench capper sits on a bench and a lever presses the bell down, while a wing capper is held in the hand and the handles squeeze the bell down. The Fermentaholics capper is a double-winged hand capper, and the FastRack and QWORK cappers are bench models. The bench capper vs wing capper comparison lines up the two styles.
More preserving guides
See every beer brewing guide and all home brewing guides.
More picks: beer brewing kits, bench vs wing cappers, bottle cap sizes and all-grain vs extract brewing.





