On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
InnoMoon Meat Grinder and Slicer Shredder Attachment for9.6/10View on Amazon - 2
ALTRA LIFE Electric Meat Grinder9.7/10View on Amazon - 3
AAOBOSI 4-in-1 Electric Meat Grinder9.7/10View on Amazon - 4
Cutluxe Carving Knife SetView on Amazon - 5
DRAGON RIOT 3-Piece Boning Butcher Knife Set 8inchView on Amazon - 6
Huusk Butcher Knife Set of 3 -Japanese Knife Set for MeatView on Amazon
Meat grinder set up is the part of the job that decides whether the grind comes out even and the cleanup stays quick. A grinder attachment fitted in the right order, with the blade seated flat against the plate and the ring snug, turns chunks of meat into a steady stream instead of a smeared paste.
Runners-up to consider
Cutluxe Carving Knife SetCheck price on Amazon
DRAGON RIOT 3-Piece Boning Butcher Knife Set 8inchCheck price on Amazon
Huusk Butcher Knife Set of 3 -Japanese Knife Set for MeatCheck price on Amazon
HarvestGearLab earns a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
Meat grinder set up: the parts in the box
Open the box on a clean counter and lay the parts out in a line so each piece is easy to see. The kit in this guide holds a stainless steel grinder body, 3 interchangeable blades, 4 grinding plates, 3 sausage stuffing tubes, a kibbe attachment and a cleaning brush, and the mixer itself is not included. Check each piece for nicks or bent edges before assembly, since a damaged blade or plate will show up in the grind. The table below lists what each part does.
| Part | What it does | In the kit |
|---|---|---|
| Grinder body | Holds the blade, plate and tubes in line | Stainless steel body |
| Blades | Cut the meat as it passes the plate | 3 interchangeable blades |
| Grinding plates | Set the grind by the size of the holes | 4 grinding plates |
| Sausage stuffing tubes | Fill casings with ground meat | 3 sausage stuffing tubes |
| Kibbe attachment | Shapes kibbe from ground meat | Included in the kit |
| Cleaning brush | Scrubs the plate holes and tubes | Included in the kit |
Fit the grinder body to the mixer
Start with the mixer switched off and the hub cover removed, then slide the grinder body onto the hub and lock it in place. The FOKIEE attachment (on Amazon) fits KitchenAid mixers of all models, so the body should seat squarely on the hub without forcing. A body that can wobble will let the blade shift while grinding, so check the lock before adding the blade, plate or tubes.
Chill the parts before grinding
Chill the grinder body, blade, plate and tubes before assembly when the meat is fresh from cold storage. The listing notes that pre-chilling the attachment gives the cleanest grind, and cold parts keep the fat firm while the meat passes through the plate. A warm grinder smears fat across the plate instead of cutting cleanly, so a rest in cold storage is worth the wait.
Choose a grinding plate
The kit holds 4 grinding plates, and the plate you pick sets the texture of the grind. A plate with wide holes gives a coarse grind that suits burgers and sausage, while a plate with fine holes gives a smooth grind that suits meatballs and veggie patties. Match the plate to the dish on the menu, and set the plates not in use aside in a dry spot so the holes stay clear.
Hold the plate up to the light and look through the holes before fitting it. A plate with a blocked hole will leave streaks of uncut meat in the grind, and a plate with a bent edge will not sit flat against the blade. Swap in a spare plate from the kit when the fitted plate looks worn, and keep the spare plates dry between uses. The parts guide at parts for meat grinder lists plates, blades and sizes in more detail.
Fit the blade and the plate
Seat the blade with the cutting edge facing the plate, then set the plate against the blade and screw the ring on until it is snug. The blade must sit flat, with no gap between blade and plate, or the meat will slip past the edge instead of being cut. Check that the blade turns freely with the plate in place before the mixer is switched on.
Never force the ring when it will not thread. Back it off, reseat the plate so it sits square, and thread the ring again. A ring that cross-threads can damage the body, and a body with damaged threads will not hold the plate flat. A snug ring is enough, and extra force on the ring will not make a dull blade cut better.
Keep a spare blade from the kit close at hand, since a blade can dull partway through a large batch. The kit holds 3 interchangeable blades, so a fresh blade is always within reach. Swap the blade when the grind starts to look smeared or the meat starts to back up in the throat, and clean the dull blade before it goes back in the box.
Attach the sausage stuffer tubes
Swap the grinding plate for a stuffer tube when the meat is ground and ready for casings. The kit holds 3 sausage stuffing tubes in different sizes, so pick the tube that matches the casing on hand. Slide the tube onto the body in place of the plate, fit the ring over it, and feed the ground meat through with the mixer running at a slow speed.
Keep the casings damp and the meat cold while stuffing, and stop to clear the tube when the flow slows. A tube that clogs will push meat back toward the mixer, so clear it early rather than forcing more meat through.
Grind in steady batches
Cut the meat into strips that fit the throat of the grinder before feeding it in. Long strips feed more evenly than cubes, and a strip that is too wide will jam at the opening. Feed the strips in a steady stream and let the blade pull each strip through before adding the next.
Clean up and store the parts
Take the attachment apart as soon as the grinding is done, while residue is still soft. Every piece snaps apart for washing, and the parts are dishwasher safe, so the pieces can go in the dishwasher or be washed with the cleaning brush that comes in the kit. Scrub the plate holes with the brush, since dried meat in a hole will block the next grind.
Wash the blades and plates right away, since meat dries fast on steel and a dried film is harder to scrub off than fresh residue. Brush the holes from each side, and check the blade edge for nicks before drying. The cleaning guide at how to clean meat grinder walks through brushes and kits for the job.
Dry each piece before it goes back in the box, and store the blades and plates where the edges will not knock against other metal. Stainless steel resists rust, but a blade stored loose in a drawer will dull against hard edges. A dry box with the parts laid flat keeps the kit ready for the next batch.
FAQ: preserving at home
Can a meat grinder attachment fit any KitchenAid mixer?
The FOKIEE attachment in this guide fits KitchenAid mixers of all models, and the mixer is not included. Check the hub on the mixer before buying, and match the attachment to the hub shape.
How many blades and plates come with the FOKIEE attachment?
The kit holds 3 interchangeable blades and 4 grinding plates, plus 3 sausage stuffing tubes, a kibbe attachment and a cleaning brush.
Why chill the attachment before grinding?
The listing notes that pre-chilling the attachment gives the cleanest grind. Cold parts keep the fat firm while the meat passes through the plate, so the blade cuts instead of smearing.
Are the parts dishwasher safe?
Yes. Every piece snaps apart for washing, and the parts are dishwasher safe. The cleaning brush in the kit handles the plate holes and tubes that need a scrub.
What do the sausage stuffing tubes do?
The tubes fit onto the grinder body in place of the plate and fill casings with ground meat. The kit holds 3 tubes in different sizes, so pick the tube that matches the casing on hand.
More preserving guides
See every harvest and processing guide and all harvest guides.
More picks: how to clean a meat grinder, meat grinder parts, meat grinder attachments and meat grinder vs meat chopper.





