On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
All American 1930 Pressure Cooker/Canner9.7/10View on Amazon - 2
Siftary 24 QT Pressure Canner with 14.5 PSI Gauge and 7-Piece9.7/10View on Amazon - 3
Presto 01781 23-Quart Pressure Canner and Cooker9.6/10View on Amazon - 4
85772 Pressure Canner Gauge Replacement Parts for PrestoView on Amazon - 5
Pressure Regulator Weight and Vent Pipe Replacement Parts FitView on Amazon - 6
Outlet Valve and Exhaust Valve Parts for Presto 409A PressureView on Amazon
Pressure canner replacement parts are the small pieces that keep a canner sealing and holding pressure: the ring, the gauge, the regulator weight and the vent parts. When one of them wears out, the canner still looks fine, but the lid may leak steam or the gauge may read wrong. This guide walks through each part in turn, shows how to match it to a canner model, and points to the checks that tell you a part is due for replacement.
Runners-up to consider
85772 Pressure Canner Gauge Replacement Parts for PrestoCheck price on Amazon
Pressure Regulator Weight and Vent Pipe Replacement Parts FitCheck price on Amazon
Outlet Valve and Exhaust Valve Parts for Presto 409A PressureCheck price on Amazon
HarvestGearLab earns a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
Pressure canner replacement parts: the short list
Most pressure canner repairs come down to a short list of parts. The table shows each one, what it does, and the first thing to check before you order.
| Part | What it does | Check before you order |
|---|---|---|
| Sealing ring, part 09985 | Seals the lid to the body so steam stays inside | Canner size in quarts and the part number on the old ring |
| Dial gauge, part 85772 | Shows the pressure inside the canner | The part number on the old gauge and the dial size |
| Regulator weight, part 50332 | Sits on the vent pipe and lets off steam | The part number on the old weight and the vent pipe size |
| Vent pipe, part 85608 | Carries steam out of the lid to the weight | The part number stamped on the old pipe |
| Air vent cover and lock | Covers and locks the vent in the lid | The part number on the old cover |
Start with the model number, not the part
Every replacement part on a pressure canner is made for a set of models, and the model number is what decides the fit. Find the model number on the canner body or lid, then look for a listing that names it. A part that fits a 23 quart canner may not fit a 16 quart canner from the same maker, so the quart size alone is not enough.
Part numbers do the same job from the other side. The sealing ring in the listings here carries part number 09985, the dial gauge carries part number 85772, and the regulator weight and vent pipe carry part numbers 50332 and 85608. Match the part number on the part you are replacing, and when the listing names a set of models, check that your model is in the set before you order. The best pressure canner guide lines up current canners by size and gauge type.
The sealing ring
The sealing ring is the gasket that sits in a groove in the lid and presses against the canner body when the lid closes. It is the part that wears first, because heat and use wear the silicone down over time. The listings here show a food-grade silicone ring, part number 09985, made for Presto 16, 18 and 23 quart canners, and heat-resistant up to 450°F (232°C).
To fit a new ring, take the old ring out of the groove, clean the groove, then work the new ring into the lid a section at a time. Open and close the lid several times to seat it, and check that it sits flat all the way around before you use the canner. The listings here sell the ring as a 2 pack, which leaves a spare on the shelf for the next change.
The dial gauge
The dial gauge is the round dial on the lid that shows the pressure inside the canner while it runs. A gauge that sticks, reads low, or has a cracked dial cannot be trusted, and a canner with a gauge you cannot trust should not be used until the gauge is checked or replaced.
The replacement gauges in the listings here carry part number 85772, which replaces part numbers 82237 and 82121, and measure 0 to 20 PSI. The TZona gauge (on Amazon) measures 2.8 by 2.0 inches, with a clear dial that is easy to read. To fit one, take the nut under the lid off, lift the old gauge and washer out, set the silicone gasket in place, then the steel gasket, and screw the nut back on. Ask your local extension office whether it can check a dial gauge, and have it checked when you fit a new one.
The regulator weight and vent pipe
The regulator weight sits on the vent pipe and controls the steam that leaves the canner. As pressure builds, the weight lifts and rocks, letting off steam in a slow, steady rhythm. The listings here sell the weight and the vent pipe together: the weight carries part number 50332 and the vent pipe carries part number 85608.
Fit the new vent pipe first, then set the weight on top of it. The weight and the pipe work as a pair, so replace them together when either one is worn or damaged. A weight that does not sit flat on the pipe, or a pipe with a blocked opening, needs attention before the canner goes back into use.
The air vent cover and lock
The air vent cover and lock is the small cover that sits over the vent in the lid. It keeps the vent clear while the canner heats and locks in place once pressure builds. The listings here show covers made for Presto canners, with part numbers 24033, 29008, 33006 and 85407, sold as a 2 pack with one to fit and one to keep as a spare.
What to skip or double-check
- Processing jars in the oven: skip it. Dry oven heat is not a safe way to process canning jars.
- Electric pressure cookers: do not use one for canning unless the maker states it is made for pressure canning.
- Parts that do not name your model: check the part number and the model list before you order.
- A gauge that sticks or reads low: have it checked before you use the canner.
- Old or secondhand canners: check the gauge, seal and safety plug before use.
What this guide does not cover
This is a parts guide. It does not give recipes, processing times, pressures, headspace figures or altitude changes. Take those from current USDA and National Center for Home Food Preservation guidance, or from a current edition of a trusted canning guide, and follow them exactly for each food. Every canner and tool guide on the site is collected in the canning section.
FAQ: preserving at home
Which sealing ring fits a canner?
Match the part number and the quart size. The ring in the listings here is part number 09985, made for Presto 16, 18 and 23 quart canners. Check the part number on your old ring and the model number on your canner before you order.
When should I replace a pressure canner gasket?
Replace it when it feels stiff, looks cracked or warped, or lets steam leak around the lid. A ring that no longer sits flat in the groove will not seal, even if it looks whole. Keep a spare on hand so a worn ring does not stop a canning day.
What does the air vent cover do?
It covers the vent in the lid while the canner heats and locks in place as pressure builds. The listings here show covers with part numbers 24033, 29008, 33006 and 85407, sold as a 2 pack with one to fit and one to keep as a spare.
Can I fit a gauge from another brand?
Only if it matches your canner. The gauge in the listings here is part number 85772, which replaces part numbers 82237 and 82121 and fits the Presto models the listing names. Match the part number first, and have a new dial gauge checked before you rely on it.
More preserving guides
See every pressure canners guide and all canning guides.
More picks: pressure canners, canning tool kits, water bath vs pressure canner and water bath canners.





