Skip to content
Independent guides to preserving gear, est. 2026

Canning, drying, storing and harvest gear for home kitchens

We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals
Canning Parts: Lids, Bands, Gaskets and Accessories Guide
Canning

Canning Parts: Lids, Bands, Gaskets and Accessories Guide

Canning parts are the lids, bands, gaskets, regulator weights and racks that keep a canner working, and this guide explains what each one does and when to replace it.

On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1FORJARS Canning Lids and RingsFORJARS Canning Lids and Rings9.6/10View on Amazon
  2. 2HekouJiub Regular Mouth Canning RingsHekouJiub Regular Mouth Canning Rings9.5/10View on Amazon
  3. 3Masontops Tough Band Wide Mouth Mason Jar Screw BandsMasontops Tough Band Wide Mouth Mason Jar Screw Bands9.6/10View on Amazon

Canning parts are the small pieces that keep a canner sealing, venting and holding pressure the way its maker intended: lids, bands, gaskets, regulator weights, vent pipes and racks. When a seal fails or steam escapes where it should not, the cause is often a worn part, and replacing that part costs far less than replacing the whole pot. This guide explains what each part does, how to match it to a canner, and when to swap it for a fresh one.

HarvestGearLab earns a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

Canning parts: the short list

Most canning parts fall into several groups. The table shows what each group does and what to check before ordering.

Part What it does Check before ordering
Sealing ring (gasket) Seals the cover to the body so pressure can build Model and quart size of the canner
Regulator weight Sits on the vent pipe and controls steam release Part number and canner brand
Vent pipe Carries steam out of the cover to the regulator weight Part number and canner brand
Air vent cover and lock Covers the vent opening in the lid Model and quart size of the canner
Wing nuts Hold the canner lid in place Model of the canner
Lid handles Give a grip for lifting the cover Model and quart size of the canner
Canning rack Keeps jars off the bottom of the pot Diameter of the pot

Match the part to the canner

Start with the brand and model stamped on the canner, then match the part number. A part that fits a Presto canner (on Amazon) does not fit an All American canner, and a Mirro part does not fit a Presto canner. Listings state the models each part fits, so compare the model on the canner with that list before ordering.

Quart size matters as well. The ANTOBLE 09985 sealing ring (on Amazon) fits Presto canners of 16, 18 and 23 quarts, while the ANTOBLE wing nuts (on Amazon) fit All American models 910, 915, 921, 925, 930 and 941, which the maker lists at 10.5, 15.5, 21.5, 25, 30 and 41.5 quarts. A ring or gasket made for one quart size may not seat in a cover made for another size. The canning pot sizes guide explains how quart size relates to jar count.

Seals and gaskets

The sealing ring, also called a gasket, sits in a groove inside the cover and forms the seal between the cover and the body. When the ring is worn, steam escapes around the rim and the canner struggles to hold pressure. The ANTOBLE 09985 sealing ring is made of food-grade silicone and comes as a 2-pack with overpressure plugs, fitting Presto canners of 16, 18 and 23 quarts. The maker recommends replacing the gasket every 1 to 2 years.

To fit a new ring, remove the old ring and plug, clean the groove and the plug hole, then work the ring into the cover a small section at a time. Push the round side of the plug, marked TOP, into the opening from the underside of the cover. Check the ring for cracks, stiffness or a loose fit before each canning season, and keep a spare on hand.

Regulator weights and vent pipes

The regulator weight and the vent pipe work as a pair: the vent pipe is fixed to the cover, and the weight sits on top of it, letting steam out in a steady rhythm while the canner holds pressure. The ANTOBLE 50332 regulator weight (on Amazon) comes with the 85608 vent pipe, and the pair fits Presto canners of 16 and 23 quarts. The Pokin vent pipe (on Amazon) is made of 304 stainless steel and fits All American canners of 15.5, 21.5, 25, 30 and 41.5 quarts, serving as the primary pressure relief valve on the cover.

The Mirro S-9898 regulator weight fits Mirro pressure cookers and canners. When the canner reaches the right temperature, the regulator jiggles and steam escapes, holding the pressure steady without adjustment. If the weight is lost or the vent pipe is clogged, replace the pair. The Presto pressure canner weight guide and the Mirro pressure canner parts guide cover each brand in more detail.

Small hardware: wing nuts, handles, lift pins and vent covers

Wing nuts clamp the cover down on All American canners, and the ANTOBLE set comes as a 6-pack that fits models 910, 915, 921, 925, 930 and 941. The nuts are made of a heat-resistant material that stays cool to the touch while the canner is hot. If a wing nut is cracked or will not tighten, replace it before the next batch, and keep the spares from the pack.

Lid handles, lift pins and air vent covers wear out in the same way. The HDWGGD cover handle fits Presto canner lids of 16 and 21 quarts and comes as a 2-pack, with screws not included. The ANTOBLE S-9709 lift pin assembly fits Mirro models in the M-0512, M-0522, M-0526, M-0534, M-0536, M-0592, M-0594, M-0596, M-0598 and M-0646 lines, and steam leaking around the lid is a sign the pin needs replacing. Air vent covers for Presto canners of 16 and 23 quarts, such as the Mzcvriru and Hasanbar parts, come as a 2-pack, so one can serve as a spare.

Racks and jar handling

A canning rack keeps jars off the bottom of the pot so heat and water can move around them. The Presto 85707 rack measures 11 inches across and is a genuine replacement part for Presto pressure canners. It also keeps food out of the cooking liquid. If the rack is bent or rusted, a replacement rack of the same diameter restores the spacing the canner was made for. The how to use a canning rack guide shows how a rack sits in the pot.

What to skip or check again

  • Parts with no model list: skip a part when the listing does not state which models it fits.
  • Parts for another brand: a Presto part does not fit a Mirro canner.
  • Worn gaskets: check the sealing ring for cracks or stiffness before each canning season.
  • Reused flat lids: buy new flat lids for each batch; jars and bands can be reused when free of chips and rust.
  • Electric pressure cookers: do not use one for canning unless the maker states it is made for pressure canning.
  • Secondhand canners: check the gauge, seal and safety plug before use, and ask a local extension office about checking a dial gauge.

What this guide does not cover

This is a parts guide. It does not give recipes, processing times, pressures, headspace figures or altitude changes. Take those from current USDA and National Center for Home Food Preservation guidance. Every canner and tool guide on the site is collected in the canning section.

FAQ: preserving at home

How do I know which canning parts fit a canner?

Match the brand and model stamped on the canner with the model list in the part listing, and check the quart size. A part made for Presto canners of 16 and 23 quarts will not fit another size or brand.

How often should a pressure canner gasket be replaced?

The maker of the ANTOBLE 09985 sealing ring recommends replacing the gasket every 1 to 2 years. Check the ring for cracks, stiffness or a loose fit before each canning season, and replace it sooner when steam escapes around the rim.

What does a regulator weight do?

The regulator weight sits on the vent pipe and lets steam out in a steady rhythm while the canner holds pressure. The ANTOBLE 50332 weight comes with the 85608 vent pipe for Presto canners of 16 and 23 quarts.

Can I replace a broken canner handle or wing nut instead of buying a new canner?

Yes. Handles, wing nuts, lift pins and vent covers are sold as replacement parts, and the ANTOBLE wing nut set comes as a 6-pack with spares.

More preserving guides

See every pressure canners guide and all canning guides.

More picks: pressure canners, Presto canning parts, Mirro pressure canner parts and canning tool kits.

Read next in the kitchen