Skip to content
Independent guides to preserving gear, est. 2026

Canning, drying, storing and harvest gear for home kitchens

We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals
Pressure Canner Repair: Common Parts to Replace
Pressure Canners

Pressure Canner Repair: Common Parts to Replace

Pressure canner repair starts with the sealing ring, the overpressure plug and the gauge, and this guide shows how to spot each worn part and match its replacement.

On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Presto 02152 17-Quart Digital Pressure CannerPresto 02152 17-Quart Digital Pressure Canner9.7/10View on Amazon
  2. 2Presto 01784 23-Quart Induction Compatible Pressure CannerPresto 01784 23-Quart Induction Compatible Pressure Canner9.7/10View on Amazon
  3. 3Presto 02154 16-Quart Digital Pressure CannerPresto 02154 16-Quart Digital Pressure Canner9.7/10View on Amazon

A counter full of tomatoes waits for the canner, and the lid will not hold a seal. Pressure canner repair starts with that moment: find the part that wore out, match its replacement to the canner model, and swap it in before the next batch. Most fixes come down to a sealing ring, an overpressure plug or a gauge fastener, and this guide walks through each part in order.

HarvestGearLab earns a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

Pressure Canner Repair: The Short List

Most pressure canner trouble comes down to the sealing ring, the overpressure plug and the gauge fastener. The table shows what each part does and which canner it fits.

Part What it does When to replace it Fits
Sealing ring 09985 Seals the lid to the body and holds pressure When the seal leaks or the ring feels hard Presto 16, 18 and 23 quart models
Overpressure plug Vents pressure if it climbs too high When the plug looks worn or cracked Presto canners that use the 09985 ring
Gauge fastener pack 82248 Holds the steam gauge tight so it reads true When the gauge wobbles or steam escapes at the gauge Presto gauges 82121, 82237 and 85772
Gasket S-3440 Seals the lid to the body When the seal leaks or the gasket feels hard Mirro models made before January 1983

Start with the symptom

Work from what the canner does wrong. Steam escaping around the lid points to the sealing ring. A gauge that wobbles, or steam hissing at the gauge, points to the gauge fastener. A plug that looks cracked or flattened points to the overpressure plug. Match the symptom to the part before ordering, and match the part to the model number on the canner.

Replace the sealing ring

Pull the old ring out of the lid groove and clean the groove before the new ring goes in. Work the new ring into the lid a small section at a time until it sits fully in place, then open and close the lid several times so it moves freely. The Presto 09985 ring is food-grade silicone, BPA-free, and heat-resistant up to 450°F (232°C), and it fits Presto models 0174510, 0175107, 0175510, 0178107, 0178209 and 0178410, which cover 16, 18 and 23 quart canners. The Ulreon 2-pack (on Amazon) ships with 4 plugs, so a spare ring stays on hand. See the how to use Presto pressure canner guide for the full routine.

ANTOBLE lists the same 09985 ring for the same Presto models, and its guidance is to replace the gasket every 1 to 2 years so the canner keeps working well. For older Mirro canners, the GUSUUI S-3440 gasket (on Amazon) fits models M-312, M-406, M-512, M-522, M-526 and M-622, but only canners manufactured before January 1983, so check the date stamp on the bottom of the canner before ordering.

Replace the overpressure plug

The overpressure plug sits in the lid and vents steam if pressure climbs too high. To swap it, remove the old plug, clean the plug hole, and push the round side of the new plug, marked “TOP”, into the opening from the underside of the cover. Open and close the cover several times after fitting so it moves freely. Plugs ship with the 09985 ring kits, so a ring order usually brings fresh plugs with it.

Fix a gauge that reads wrong

A loose gauge reads wrong and lets steam escape at the fitting. The Gfdoso 82248 fastener (on Amazon) pack fits Presto steam gauge models 82121, 82237 and 85772, and each pack holds 5 washers, 5 nuts and 5 gaskets in stainless steel and rubber. Swap the worn washer, nut and gasket at the gauge, and the gauge should sit tight and read true. If the gauge still reads wrong after the fastener is swapped, the gauge itself is the part to replace, and a local extension office can check a dial gauge.

When to stop and get help

Some faults sit past the replaceable parts. A lid that will not close, a body that is dented or warped, or a vent that stays blocked after cleaning all call for a pro or a new canner, not another part. Do not heat jars in the oven, and do not can in an electric pressure cooker unless the maker states it is made for pressure canning. For recipes, times and pressures, follow current USDA and National Center for Home Food Preservation guidance. Compare current models in the best pressure canner guide.

FAQ: preserving at home

How often should I replace a pressure canner gasket?

ANTOBLE lists replacement every 1 to 2 years for the 09985 gasket. Replace sooner if the ring feels hard or the lid leaks steam.

How do I know which sealing ring fits my canner?

Match the ring to the model number on the canner. The 09985 ring fits Presto models 0174510, 0175107, 0175510, 0178107, 0178209 and 0178410, and the S-3440 gasket fits Mirro models made before January 1983.

What comes in a gauge fastener pack?

The Gfdoso 82248 pack holds 5 washers, 5 nuts and 5 gaskets for Presto steam gauge models 82121, 82237 and 85772.

Can I replace a pressure canner gasket myself?

Yes. Remove the old ring and plug, clean the groove and the plug hole, work the new ring in a small section at a time, and open and close the lid several times so it moves freely.

My Mirro canner is old. Which gasket fits it?

The GUSUUI S-3440 gasket fits Mirro models M-312, M-406, M-512, M-522, M-526 and M-622 manufactured before January 1983. Check the date stamp on the bottom of the canner to confirm the year.

More preserving guides

See every pressure canners guide and all canning guides.

More picks: pressure canner replacement parts, Presto canning parts, Mirro pressure canner parts and All American canner parts.

Read next in the kitchen